Comfort 300 LR

Comfort 300 LR is for anyone who wants ventilation with highly efficient heat recovery and comfort heating.

These systems extract hot, humid air from e.g. the kitchen, bathroom and utility room, at the same time removing dust particles, moisture and odours from the home. Furthermore, the energy from the extract air is used to heat the incoming air. Comfort 300 LR can replace 400 m³ air per hour.

The systems can be equipped with supplementary heating coils that can be connected to an electric or central heating system. The system will produce a comfortable incoming air temperature even in the coldest winter weather. When you buy a Comfort system, you get a comfortable and healthy indoor climate and cost savings on your heating bill.

Comfort 300 LR is suitable for locating in an attic space. 

The Comfort 300 LR is an energy-efficient ventilation unit with heat recovery for homes and smaller commercial buildings with a ventilation requirement of up to 400 m3/h.

This unit has been thoroughly tested, with improvements being continually made during its manufacture for more than 15 years. These improvements focused on low energy consumption, easy user operation and maintenance.

As a result, service access is available from both sides, which means that the Comfort 300 LR can be used as a “right” or “left” model. This offers a flexible and easy installation.

The Comfort 300 LR is factory tested and ready for use. Installation and commissioning must be performed by an authorised electrician.

Dimensions (WxDxH) 1000 x 508 x 560 mm
Weight 45/33 kg (*1)
Plate type casing Aluzinc steel plate
Heat exchanger type Polyethylenterephthalat counter flow heat exchanger with aluminium casing
Fan type EC, constant volume
Filter class Standard ISO Coarse >90% (G4)
Duct connections Ø 160 mm
Condensate drain PVC, Ø 20 ×1,5 mm
Supply voltage 230 V (±10 %), 50/60 HZ
Max. input/power 270 W/2,2 A
Tightness class IP31
Standby power 3 W
Ambient temperature -20/+40 °C
Lækage klassifikation A1 (*2)
Heat loss 0,82 W/m2K (3*)
Heat loss classification T2

Ecodesign/ERP data

Fan data
Motordata (optimalt driftspunkt)

*1 33 kg is without side plates and exchanger
*2 Testet according to EN13141-7
*3 Testet according to EN1886

CO2-sensor – CTS 602 control

With a CO2-sensor installed, the ventilation speed can be pre-programmed with CTS 602 to run at a higher ventilation steps when CO2 reaches high level in the extract air. CO2-level is programmable.

Electrical pre-heating element (Frost protection)

An electrical pre-heating element heats up the outdoor air before it enters the unit. This avoids having to defrost the unit, resulting in a loss of power.

There are temperature sensors supplied to be fitted in the ducts.

Electrical heating element incl. regulation

When you fit an electrical heating surface, you can raise the fresh air temperature to the desired level at any time. The electrical heating surface is supplied ready to fit into the fresh air duct and, for easy fitting, the device is pre-fitted with all the required sensors.


Water heating element incl. regulation

The supply temperature can always be raised to the required level using a water heating element. The water heating element is designed to be built into the unit and must be connected to the primary heating supply. Supplied with two-way adjustment valve, temperature sensor and frost thermostat (expansion PCB required).


An EM-box allows heat recovery from the air from the range hood and thereby helps to heat the supply air. The EM-box is equipped with a steel filter which efficiently cleans the range hood air of fat particles and thereby protects the system.


Expansion PCB

The expansion PCB provides additional functions for the CTS 602 control unit.

Pollen filter - ISO ePM1 50-65%

A pollen filter class ISO ePM1 50-65% can be fitted in the unit. The pollen filter is fitted with the ISO Coarse >90% (G4) plate filter.

Installation kit

The installation kit comprises of four vibration absorbers and a water trap for the condensation outlet. The water trap can be ordered separately.

Heating cable

To protect the condensation outlet against frost, a 3 metre-long self-regulating heating cable can be ordered.


Data sheet
Comfort 300 LR data sheet

Ventilation and indoor climate solutions

Data sheet accessories
Heating elements

DWG drawing
Comfort 300 DWG  drawing

3D files
Comfort 300LR (right/left) 3D file

If you want to convert STEP files to Revit, do the following:
Import the STEP file to Autocad, export it as a 3D DWG file and then import the file into Revit.

Installation manual
Comfort 300LR with CTS602 control HMI Touch panel

User manual
Comfort 300LR with CTS602 control HMI Touch panel

Software manual
Comfort 300LR with CTS602 control HMI Touch panel

CTS602 light Modbus protocol


SEC* average climate - 38.9 kWh/(m2.a)
SEC* cold climate - 77.1 kWh/(m2.a)
SEC* warm climate - 14.5 kWh/(m2.a)
SEC-Class A
Type Two-way ventilation unit for residential
Type of drive Variable speed drive
Type of heat recovery system Recuperative
(counterflow heat exchanger)
Thermal efficiency
of heat recovery
87 %
Maximum flow rate 400 m3/h (100 Pa)
Electric power input of fan drive, including any motor control equipment, at maximum flow rate 108 W
Sound power level (LWA) 37 dB(A)
Reference flow rate 0.078 m3/s (280 m3/h)
Reference pressure difference 50 Pa
SPI 0.27 W/(m3/h)
Central demand control 0.85
Maximum internal leakage 1.8 %
Maximum external leakage 1.12 %
Visual filter warning An alarm on the user panel appears when filters need changing.
To maintain the performance and energy efficiency of the unit it is very important to change filters regularly.
Disassembly instructions

* Specific energy consumption


AEC - annual electricity consumption 289 kWh/year (100 m2)
AHS** average climate 4548 kWh (100 m2)
AHS** cold climate 8898 kWh (100 m2)
AHS** warm climate 2057 kWh (100 m2)

** Annual heating saved


Capacity of standard unit as a function of af qv and Pt, ext.

SEL values according to EN 13141-7 are for standard units with standard filters ISO Coarse >90% (G4) and without heating element.

SEL values comprise the unit´s total power comsumption excl. control.

Conversion factior: J/m3 : 3600 = W/m3/h

Attention! The SEL values are measured and stated as a total value for both fans.

Temperature efficiency

Temperature efficiency for units with counterflow heat exchanger according to EN13141-7




Sound data

Sound data for qV = 200 m3/h and Pt, ext = 100 Pa according to EN 9614-2 for surfaces and EN 5136 for ducts.

Sound output level LWA drops with falling air volume and falling back pressure.

Sound output level LpA at a given distance will depend on acoustic conditions in the place of installation.


All dimensions are in mm.

1: Fresh air
2: Supply air
3: Extract air
4: Discharge air
5: Condensate drain
6: Electric and water heating

The Comfort 300LR is controlled using its CTS 602 HMI touch panel, featuring a wide range of functions, e.g., menu-controlled operation, weekly programme settings, filter monitor with timer, fan speed adjustment, summer bypass, supply-heating element control, error messages etc.

The CTS 602 comes with factory settings, including a default setting which can be customised to operational requirements to achieve optimum operation and utilisation of the system.

There is an option for selecting between 2 front page images for the main screen.

Operating instructions for the CTS 602 can be found in a separate user manual supplied with the unit.


1: Fresh air
2: Supply air
3: Extract air
4: Discharge air
5: Condensate drain
6: Electric and water heating

T2/T7: Supply air sensor
T9/TC: Heating element frost protection
T3: Extract air sensor
T4: Discharge air and defrost sensor
T8: Fresh air sensor


Functional overview CTS 602 overview

Functional overview  

+ Standard

- Accessories

3 levels The control function is divided into 3 levels: User/Service/Factory with various options at each level  +
Weekly plan The unit has 3 weekly programmes (with a factory setting of “off”)
• Programme 1: for working families
• Programme 2: for stay-at-home families
• Programme 3: for businesses
There is also an option for you to set your own weekly programme.
User option
1 & 2
This allows you to override the operating mode in the main menu via an external potential-free contact or PIR sensor.  +
Datalog Possible to log data. Kapacity 46.000 logs
• Adjustable between 1 and 120 minutes
• If “OFF”, only events and alarms are logged
Filter monitor Filter monitor with timer (factory setting of 90 days). Adjustable to 30/90/180/360 days.  +


Bypassing the outdoor air reduces heat recovery when heat recovery are not needed.  +
Air quality Allows you to choose whether to switch humidity sensors and/or CO2 sensors on and off.  +/-
Humidity control Allows you to set a higher or lower ventilation step in the case of high/low air humidity.  +
Summer/Winter operation Possible to set operation for summer and winter.  +
Winter low Allows you to select a low ventilation step in the case of low outside temperatures.  
Defrost function Temperature-based automatic function for defrosting the heat exchanger.  +
Frost protection In case of failing heating system, the unit is turned off to avoid further cooling with a risk of the water heating coil frost bursting.  +
Room low Stops the unit at a low room temperature. Hereby is cooling of the home avoided in case of a failing central heating system. Standard set to OFF. Can be set from 1 to 20 degrees and is controlled by:
• T3 EXHAUST (extract air)
Air volume Allows you to set four ventilation steps stepless. 
Supply air and extract air are set individually.
Step 1 < 25%  -  Step 2 < 45%  -  Step 3 < 70%  -  Step 4 < 100%
External firealarm

Possible to connect the unit to external firealarm.

Joint alarm Outlet for joint alarm  -
Intake air control Allows you to set the regulator to control the intake air temperature/supply air
(only available if the control unit has been configured for a supply-heating element).
External water heating element • Temperature sensor T7 is an supply air sensor
• Integrated frost protection for external water heating element
• Motorised valve and circulation pump control unit
External electric heating element • Temperature sensor T7 is an supply air sensor
• Overheating protection
Delayed start-up There is a possibility for a delayed start-up by the fans, when a closing damper is installed.  +
Reset Allows you to restore the factory settings.  +
Manual test Allows you to test the unit’s functions manually.  +
Language Option for setting the relevant language (Danish/Finnish/Norwegian/Swedish/German/English/French/Polish).  +


About Nilan

Domestic solutions

Commercial Solutions 

Find Dealer

Find din Nilan Forhandler


Helsinki, Finland
13th - 15th of April 2021

Odense, Denmark
21st - 23rd April of 2021
Nilan A/S · Nilanvej 2 · 8722 Hedensted · Denmark · Phone +4576752500 ·
Privacy- and cookiepolicy